Will wood movement in this project be a factor?? - square wood coffee table
I am a butcher-block top for a coffee table. Be 2.5 to 3 inches thick. I use 2x4 White Wooden 8-foot Lowe. The pieces are set with endgrain up / down. Visual look like little squares and rectangles side by side in a view from above, so I'm stuck at 2.5 to 3 pieces of one page to another inch.
I've heard, 2x4 (are treated) is still very wet, dry in the store and have for a long time to prevent the movement of the wood.
I must take this into account, because I have to do with blocking the short side pieces on the top of the butcher too? Or I can go to court and) the subject of the 2x4 (Lowe's or any other DIY store? There is an air-conditioning, a coffee table in the room, and I want to avoid separating still occur.
Sunday, January 24, 2010
Square Wood Coffee Table Will Wood Movement In This Project Be A Factor??
Subscribe to:
Post Comments (Atom)
10 comments:
I guaran-tee-tar and parts are separated. White HD is the term generally refers to radiata pine. depending on where you live, save in the size of 2x4 pine or fir tree in a box. too soft for his own purposes. So we have to do try, you need a dense and strong wood grained low humidity, such as maple, ash, Lyptus. You can shop online by your desired dimensions. Try the Web-Search for hardwoods. or rockler.com
I hope that helps.
I guaran-tee-tar and parts are separated. White HD is the term generally refers to radiata pine. depending on where you live, save in the size of 2x4 pine or fir tree in a box. too soft for his own purposes. So we have to do try, you need a dense and strong wood grained low humidity, such as maple, ash, Lyptus. You can shop online by your desired dimensions. Try the Web-Search for hardwoods. or rockler.com
I hope that helps.
Oven-dried wood is still a moisture content between 5% to 7%, so that it is still in decline, to dry up further. like, very dry and close-grained wood for this guy up there. Poplars, or you hit a very hard wood such as walnut. tighter grain, the best since I moved the least.
Butcher block is hardwood customarly.
They are not with what you can see, happy
Cases of "2 x 4
Waiting for the end grain to split easily when only 3 cm deep
4-6 'space of a typical coffee table.
If "rabbit" structural wood.
Cut all the parts and then let them ask about a month when the dry.
If you do not Klin dry wood
Here the problem is with the exposure of end grain. As you may know, have or not is a good question, the wood shrinks swollen year. Therefore, if you have a 2X4 shrink and swell in the "2" and "4" direction, but not on the 8th. Once you have the 2x4 2.5 "or 3" and place them all together, cut them to shrink and swell in all directions do not want and not how they could bear.
Yes, should be) the movement of wood is an important factor in your project, but it is small (coffee table instead of life is no big problem. Go to the oven if you can afford. This was the title sitting on the air in the room with one or two weeks. Em good tail clip 'em well, and get a finished product or at least an abrasive sealer for all parties as soon as possible.
Some other advice grain of sand is difficult to be very careful to align the beginning of the upper and lower body. Note also that the corners of the grain final table chip is for you to be easier to WORSolid Edge ka at the top.
I agree that the factor is the inflammation of a problem in this area. Something that my father, when a similar project there was a beautiful wooden frame with "Pieces" and inside pocket. There were about 1 / 8 "(or less) from top of the squares (or, possibly, extreme 2x4), the upper part of the". He used a transparent layer (a type of polyurethane, I thought that they have a "thick paint", as it was years ago can not exceed) the whole thing, closing in to make sure that again the same fence. It was beautiful.
Maintenance of wood in the room where you place furniture in a while is a must. I expect that the pieces after SA for some time to adjust to the wood first cut.
I agree that the factor is the inflammation of a problem in this area. Something that my father, when a similar project there was a beautiful wooden frame with "Pieces" and inside pocket. There were about 1 / 8 "(or less) from top of the squares (or, possibly, extreme 2x4), the upper part of the". He used a transparent layer (a type of polyurethane, I thought that they have a "thick paint", as it was years ago can not exceed) the whole thing, closing in to make sure that again the same fence. It was beautiful.
Maintenance of wood in the room where you place furniture in a while is a must. I expect that the pieces after SA for some time to adjust to the wood first cut.
If possible, try the device in the room where the table) (living room and leave a minimum of one week. This allows the wood to the temperature and humidity before used to be glued.
After weeks of a cut hand, you stick the wood into the desired size and together. With the glue in small chunks, then add the two parts together, etc. Make sure your staples or bar clamps with plasticizers to form a strong bond between the pieces of wood. Otherwise, you will fall to pieces and away from the table. Leave claws on at least 24 hours prior to the consolidation of sections.
Post a Comment